![]() |
![]() ![]() ![]() |
Real Life StoriesTake a look at what our customers are saying: RV Magazine January/February 2014 Tech & How-To section goes through the installation and testing of a deep PML 6L80 transmission pan on a 2012 Chevrolet Silverado. Here's a quote from the end of the article: "Our testing route took us on a 26-mile loop, up and down 6-percent grades the whole way. On the final hill where we noted our temperatures it takes about 10 minutes to reach the summit at 55mph. Before the PML pan, our transmission temperature measured 159 degrees at the base of the hill and 210 degrees at the top. Once over the top and coasting down the backside, the temperature continued to rise, hitting 218 degrees before starting to cool down five or six minutes later. With the PML pan, our temperature was 160 degrees at the base and 192 degrees at the summit. That’s a pretty decent difference, but what was really fun was how quickly it cooled back down. Almost immediately after cresting the hill, the temp began to drop, more than 5 degrees in about a minute. Impressive." Blattenberg, Adam. "Transmission Stamina." RV Magazine January/February 2014: 52-4. Print. "Hi Guys, I have purchased a rear cover for my 2002 Chevy dually. It was a VERY NICE cover. Nice hardware also, looks GREAT on the truck, many questions where I got it. I will spread the word of your quality products. I will be buying the Allision trans pan from you next." "Awesome pan. Painted mine and left it sitting in front of my 1998 Dodge Diesel - a lot of front end weight. Forgot about it while it was drying and got into the truck to drive off. Cliped the side of the pan and slid it under the truck. Any other stock pan would have been toast. No damage whatsoever. Thanks for the good product." "Hi, recvd my transmission pan the other day, installed it Saturday. Fit great and look fantastic! ! Thanks for a great product, and getting it out so quickly.........! ! !"
"I just wanted to thank you for the terrific customer service. I don’t think I’ve ever had quicker mail order delivery in my life. Thanks and I’ll be sure to share my experience with my friends and board members on the forums I frequent."
"David "Hi, I just received one of your powdercoated tranmission pans today, and WOW, this is one NICE piece! I looked around a bit for a nice aftermarket pan, and yours was one of the first ones I found, and I'm glad I made the purchase. I'm very impressed with the quality of the casting and the finish. This is one beefy bad boy that looks nice, to boot! And I'm also glad to support a company that still does it's work here in the good 'ol USA! This pan is going to be used on my AMERICAN MOTORS AMX, so I'm glad I was able to use an AMERICAN part! My car is pretty high profile, so you can be darn sure that your pan will be getting lots of good press. :) Thanks." "I got my PML differential cover in the mail the other day and decided to install it this morning. The cover is a sand cast aluminum piece that adds an additional quart of capacity to the rear end, it also has a magnetic drain plug. I have wanted to try one of these covers because it is reasonably priced, adds capacity, allows easy draining in the future, and seals using all the factory bolts and the factory gasket, it might add additional cooling with the fins but that may be negligable. The install was easy just bolt on."
"With the use of your pan and AMSOIL Synthetic lubricants I was able to attain 72 Degrees F lower operaturing temperature according to the transmission shop where I had the pan installed. Sincerest appreciation."
At PML, it is our goal to provide you with great products and service. We welcome your feedback to let us know how you are doing. If you have a story about our products, please drop us a note (we like pictures of your vehicle too). |
|
PML, Inc. 201 W. Beach Avenue Inglewood, CA 90302 310-671-4345 www.YourCovers.com yourcovers@pmli.com |
|
Copyright 2000-2019, PML, Inc. |