Volume: 3.25 quarts over stock
Dimensions: Click here for dimensions.
Number of Bolts: 12
PML AB60E, AB60F transmission pan includes transmission pan, custom gasket, bolts, fill plug and magnetic drain plug.
- Extra fluid capacity
- Cooling fins to dissipate heat
- Thick flange for a secure seal
- Interior baffles to reduce sloshing
- Shape clears frame cross members
- Does not hang below frame for ground clearance
- Heavy duty construction
- Drain hole on the side and magnetic drain plug included
- New mounting bolts included
We have one of these transmission pans on SPECIAL: Special 436
The 6 speed AB60E, AB60F transmission may be found in Toyota and Lexus trucks and SUVs such as:
- Toyota Landcruiser 5.7L, 2009 to 2015 — check for skid plate
- Toyota Landcruiser Series 200 and Series 79 (Australia) — check for skid plate
- Toyota Sequoia 5.7L, 2008 to 2018
- Toyota Tundra 5.7L, 2007 to 2018
- Lexus LX570 5.7 and some 4.5, 2008 to 2018
Always check your vehicle configuration and clearance before ordering. Verify that your vehicle has an AB60 transmission and has space for a larger aftermarket pan.
Vehicle with skid plates may not have space for this extra capacity transmission oil pan with the skid plate installed. A spacer for the skid plate may be possible.
This PML transmission pan will not work with the stock gasket. A gasket is included with the pan.
This pan has been installed on:
- 2017 Tundra with Skid Plate
- 2016 Tundra 5.7 with Magnuson Supercharger
- 2016 Tundra 5.7L
- 2008 Tundra 5.7L 4WD
- 2008 Tundra 5.7L Crew Max 4x4 AB60F
- 2013 Land Cruiser 5.7L 4WD
- Land Cruiser Series 79 (Australia)
- Land Cruiser Series 200 (Australia)
2017 Tundra with Skid Plate
Richard installed this pan on his 2017 Toyota Tundra Limited 5.7 with full skid plates. There was plenty of clearance between the skid plate and the bottom of the deeper PML pan.
2016 Tundra with Magnuson Supercharger
Carl installed this PML transmission pan on his 2016 Toyota Tundra 5.7 with a Magnuson Supercharger.
2016 Tundra AB6OE stock transmission pan
PML transmission pan installed on a 2016 Tundra AB6OE
Click on image to view larger in a new tab or window.
2016 Tundra 5.7L
Matt installed this PML transmission pan on his 2016 Toyota Tundra 5.7L. He also installed the temperature sending unit and gage.
2008 Tundra 5.7L 4WD
Orsy installed this pan on his 2008 Tundra 4x4 iForce 5.7. The installation went smoothly and took about 1 1/2 hours.
2008 Toyota Tundra 5.7 4WD
Tundra Stock Transmission Pan
Supplies for Installation PML Pan
Tundra Transmission Filter PML Transmission Pan Installed on a 2008 Tundra PML Transmission Pan Installed on a 2008 Tundra
Click on image to view larger.
Video of Installation on a 2008 Tundra
2008 Tundra 5.7L Crew Max 4x4 AB60F
Steve installed this PML transmission oil pan on his 2008 Tundra. When he was removing the stock pan, four stock bolts snapped during removal and he had to drill them out. Other than that install was great and simple. He used the PML cork gaskets for this installation. His transmission fluid temperatures dropped about 4 degrees Celsius at maximum running temperature, which is "awesome". Pan sits right flush with the frame and took the estimated 3 1/4 quarts.
2013 Land Cruiser 5.7L 4WD
This 2013 Land Cruiser removed the skid plate for the PML extra capacity transmission pan. The customer decided on Toyota Orange RTV instead of a gasket.
2013 Toyota Land Cruiser 5.7 4WD
Materials needed to install PML transmission oil pan on Land Cruiser
Stock transmission oil pan and skid plate on Land Cruiser
PML pan installed on 2013 Land Cruiser using RTV. PML pan installed on 2013 Land Cruiser, drain plug shown. Click on an image to view larger.
Land Cruiser Series 79 (Australia)
The images below show this pan installed on an Australian Land Cruiser Series 79. In one corner the pan is very close to the drive shaft but there is not contact. Photo was taken with the rear cross member removed.
PML AB60 transmission pan installed on a Land Cruiser 79 in Australia
PML AB60 transmission pan just clears the drive shaft on a Land Cruiser 79
Click on an image to view larger in a separate tab or window.
Land Cruiser Series 200 (Australia)
On Australian Land Cruiser Series 200, the skid plate interferes with the PML pan. The pan fits on the transmission but the skid plate does not provide enough clearance for the larger PML pan. In the pictures shown below, a customer tries adding spacers to the lower the skid plate for more clearance. More space was still needed so this customer was going to look into a custom skid plate.
Trying to install a PML AB60 transmission pan on a Land Cruiser 79 in Australia
Spacers on a skid plate for a deep PML AB60 transmission pan on a Land Cruiser 200 in Australia, skid plate still hit pan
Click on an image to view larger in a separate tab or window.
Transmission Filter and Gasket
AB60E, AB60F transmission and filter
AB60E, AB60F stock filter
PML AB60E, AB60F heavy duty transmission pan with PML gasket, PML pan has baffles on the inside
PML cork composite gasket for our AB60E, AB60F transmission pan
Click on an image to view larger.
This PML transmission pan works with the stock filter, available from a Toyota dealer or an auto parts store. Baffles on the inside of the PML pan reduce sloshing, direct the flow of fluid toward the pickup, and aid in heat dissipation.
This PML transmission pan will not work with the stock gasket. PML includes a cork gasket, of our own design, for this transmission pan. Some prefer to use silicon "gasket maker" which also will make a great seal. Order additional PML AB60 transmission pan cork gaskets here: PML Gasket.
The PML gasket will not work with the stock pan.
Drain, Level Check and Optional Temperature Sending Unit Locations
PML located the drain plug on the left side of the pan. This is the driver side on US vehicles. On the side of the pan, the drain plug is less likely to get damaged.
The level check hole is on the right (passenger) side, in the same location as the stock hole. This hole can also be used to fill.
PML designed the pan with two locations that can be drilled and tapped for a temperature sending unit if needed. One location is on each side. If you would like PML to drill and tap hole, the machining charge is per hole. A plug for the hole is included.
The standard size is 1/8 NPT. Call or email if you need a different size.